Titan Track Ceiling Storage Rack is great for Overhead Garage storage.
Heavy Duty Storage Solutions
Titan Track is heavy duty, garage ceiling storage system made of corrosion resistant rigid PVC material. The hooks are zinc plated, rubber coated and assembled with a sliding block for easy adjustment. The ability to slide and rotate the hooks makes it easy to hang those hard to hang items. Perfect for hanging bikes, lawn and garden equipment and sporting goods. Our Ceiling storage rack is available in three lengths, 50" 74" and 98" or can be cut down to any length and additional hooks can easily be added. Great overhead garage storage of those out of season items. Use Titan Track in the garage, basement workshop, fish house, garden shed, pole barn, or utility trailer.
TITAN TRACK IS A . . . . .
MULTI USE CEILING STORAGE RACK WITH SLIDING AND ROTATING HOOKS FOR EASY ADJUSTABILITY
Titan Track is a perfect solution for hanging and storing your bikes to free up floor space in your garage or storage unit. Our track system allows you to hang your bikes and slide them together to make optimal use of overhead garage storage space. Alternate the direction of your bikes to get them closer together. Freeing up floor space with our garage ceiling storage system will allow you to park your vehicle under your bicycles when they are not in use or stored during the off-season. Titan Track works equally as well to hang all of your other gear. Whether you are an athlete, sportsman, golfer, gardener or just need to store those out of season items; Titan Track can help you with your garage organization and more.
The Titan Track system comes fully assembled with mounting hardware. Available in 50" with 5 hooks, 74" with 7 hooks and 98" with 9 hooks. Extra hooks can easily be added to customize our track to fit your needs. Maximum load is 50 pounds per hook. Titan Track is strong, versatile and easy to install. Installation holes are pre-drilled to align with ceiling joists and additional holes can easily be added. Backed by a 10 year warranty!
Installing The Titan Track System
WARNING
Must be anchored to ceiling joist, screws need to penetrate ceiling joist a minimum of 1-1/8 inch. Some applications may require longer screws.
DO NOT USE SHEET ROCK ANCHORS
Mounting Holes are predrilled at 16 and 24 inch on center. Additional holes may be drilled if necessary. Tracks may also be cut to a shorter length.
Hay Boguetes de colgar esta a 16 y 24 pulgadas del centro. Puede hacer más boquetes si, los necesita, también puede a cortar los rieles.
1) locate ceiling joists and mark the locations.
localizar las vigas. Marcar las posicíones de las vigas.
2) Check for joist using a small nail. WARNING: Tracks must be mounted to ceiling joist. DO NOT use sheet rock anchors.
Busque la viga con un calvito. CUIDADO: cuelgue los rieles a las vigas con tornillos, NO USE anclajes de tabla roca.
3) Hold track in position and mark hole locations.
Sujete el riel y riel y marque la posición de los boquetes.
4) Drill small pilot holes with 1/8 inch drill bit.
Taladre boquetes pilotos a 0.125 pulgados.
5) Install track using washers and screws.
Instale el riel con arandelas y tornillos.
1) Take axle-to-axle measurement of the bikes you want to hang and take and average. This should be approximately 38-42 inches.
Mida la distancia entre los ejes de cada bicicleta y tome la media. (aproximadamente 38-42 pulgadas)ara tener el espaciamiento correcto.
2) If mounting parallel to ceiling joist additional backing may need to be added for proper spacing.
Si se montan paralelos a la viga del techo es posible que necesite respaldo adicional para tener el espaciamiento correcto.
Tracks mounted parallel to the ceiling joist.
Rieles montados paralelos a la viga.What's something exciting your business offers? Say it here.
3) Tracks mounted across ceiling joist.
Rieles montados en perpendicular a las vig
Two tracks may be hung parallel for hanging bikes horizontal
Se puede montar los rieles paralelo para guardar las bicicletas.
INSTALLING ADDITIONAL HOOK
1) Remove Screws and End Caps 2) Insert Hooks Assembly into Track 3) Re-Install End Caps and Screws
